SON Allen Key Fitting Front Quick Release Skewer for 74mm OLN Brompton Hubs
£8.99
was
£8.99
was
Manufacturer :
SJS Cycles part number :
Manufacturer part number :
Details
Bushing and nut made of stainless steel.
For width 74mm.
The thread and bolt head should be greased, but not the shaft of the skewer.
Fasten to a torque of 8-10 Nm.
Check the tightening torque after 300 km.
For width 74mm.
The thread and bolt head should be greased, but not the shaft of the skewer.
Fasten to a torque of 8-10 Nm.
Check the tightening torque after 300 km.
Specification
Downloads
Download File
Questions & Answers (7)
Can I use this with Dahon Mu Uno?
By anthony thomas
02 Jul 2021
SJS Customer Service:
Thank you for your enquiry, yes will be fine
Can I use this with Dahon Mu Uno?
By tony thomas
27 Jun 2021
SJS Customer Service:
Thank you for your enquiry, yes will fit fine
WD 28/06/21
WD 28/06/21
What is the diameter of the rod?
By Alexandre Azzalini
01 May 2021
What is the diameter of the rod? My SP dynamo (74mm) has got a 5mm hole.
SJS Customer Service:
These are 5mm, suitable for an SP dynamo.
Thanks - 04/05/21 RH
Thanks - 04/05/21 RH
Does it suit for a 83mm front hub for on a kids bike?
By romain
11 May 2020
SJS Customer Service:
most kids bikes are not QR, this fits through a hollow axle. IF you have a hollow axle I don't think this (which OUGHT to be 9mm too short will work, unless you have VERY thin dropouts (this would be OK for 74mm hub with 6mm thick dropouts) RT
Is this suitable for Brompton front hooks?
By Nicolas
14 May 2018
I have an old T5 Brommie and it features a hook at the fork, enabling the fork to be fixed in the folded state.
This hook, of course, adds some distance to the axle's length necessary. So it would do for a skewer as well, I assume. Would this skewer have this additional length?
This hook, of course, adds some distance to the axle's length necessary. So it would do for a skewer as well, I assume. Would this skewer have this additional length?
SJS Customer Service:
The best we can recommend is - SJS Cycles part number : 13615
Thanks
Thanks
Skewer For Shutter Precision Dynamo Hub / Brompton Front
By Jonathan
30 Aug 2014
I have just built a SP dynamo hub / Brompton front wheel with parts supplied by yourselves. All good and thanks for the advice re spoke lengths, it worked perfectly.
Now to put the wheel on the bike.
Is this the right skewer I need for the hub / Brompton front wheel? It's a standard M type bike steel 3 speed.
Kind regards. JK
Now to put the wheel on the bike.
Is this the right skewer I need for the hub / Brompton front wheel? It's a standard M type bike steel 3 speed.
Kind regards. JK
SJS Customer Service:
Hi,
Yes, this is the correct skewer you need for fitting a front hub to a Brompton.
Thanks.
Yes, this is the correct skewer you need for fitting a front hub to a Brompton.
Thanks.
Qr Skewer For Single Speed Brompton Rear Axle?
By Ben
06 Aug 2014
Can I use this for the rear axle? If not, what do you suggest I do?
SJS Customer Service:
Hi,
The rear axle on a single speed Brompton should be a standard axle with nuts to tighten against the frame. All Brompton hubs aside from the dynamo ones use a screw on nut axle system.
Thanks.
The rear axle on a single speed Brompton should be a standard axle with nuts to tighten against the frame. All Brompton hubs aside from the dynamo ones use a screw on nut axle system.
Thanks.