Call us on 01278 441500 [email protected]
Home > Accessories > Trailers > Trailer Spares - Hitches & Fittings

BOB YAK Solid Axle Nutz - Choose Thread Type

Customer Reviews (1)
5 / 5| Write your review
£65.00
was
View supersize image  
Email me photo
Type
£65.00 Please note this product has selling restrictions to your country. was
Manufacturer : 
SJS Cycles part number : 
Manufacturer part number : 
Details
Per pair.

Available in the following sizes:
- 10 x 1 Thread Modern Shimano Axle (Article No. 141124002)
- 3/8 x 26 Thread Suzue / Traditional English Axles (Article No. 141126002)
- Sachs / Sturmey 3 x 7 Thread hub gear axle (Article No. 141125002)
- 3/8 x 24 Thread - Rare (Article No. 141127002)
Product Reviews (1)
Questions & Answers (21) Q & A
Specification
Downloads
Download File  
Product Reviews (1)
Overall Product Rating 5 / 5
Works but expensive
By James
12 Oct 2024
5 / 5
I recommend this product
ConsCost
ProsWorks
Make sure you get the right size for your hub.
Questions & Answers (21)
Ribble e-bike with Mahle hub?
By
22 Jun 2022
Any idea of any of these are compatible? Thanks
One of them should be, but yo need to check what thread your hubs axle uses first.

JK 23.06.22
I have a bike with a Sturmey 5 speed hub, with shifting rods/cables entering the hub both sides
By
29 Apr 2020
Are there Bob Nuts available for traditional Sturmey hub gears, where the shift rod enters the hub through the centre of the retaining nut? Thanks
yes, SJS Cycles part number : 1075TS RT01/05/2020
I have a Trek Superfly 8, 2015 harddtail. I need to fit an Ibex. How?
By
06 Sep 2019
I have a new Robert axle project axle with one side specific for fitting a bob nut. It sides on the bit sticking out and it sucures on with a nut. The new wheel axle is long enough to fit the bit that the nutz axle on the other side slides over. BUT, I need to figure out how to fit the nutz on the other side. The diameter of the bob nutz is too small for it to screw on. I guess I need a slidy axle bit for the nutz to fit over the hub axle but where do I get it? The Robert Axle project sent only one plain flat ring of metal for the drive side...? I'm so confused. Please help.
Unfortunately we have very little experience of fitting these although we sell quite a few; we would recommend speaking to RAP.

https://robertaxleproject.com/
https://robertaxleproject.com/contact-us/
[email protected]

Thanks - 10/09/19
Which option for Alfine 11
By
01 Jul 2019
You specify 2 different options in your answers regarding Alfine 11 hubs which is right 3/8 by 26 or 10x1
Alfines are 3/8 x 26 thread!

Thanks - 02/07/19
Are any of these options compatible with a brompton folding bike rear axle?
By
21 Sep 2018
If so which should I pick?
Hi please direct your question to [email protected] with details of the hub in your Brompton. They will be able to advise. Thanks.
Alfine 11 Gates Carbon Drive
By
17 Apr 2018
What kind of nutz do I need for a bike with Gates Carbon Drive and Alfine 11? My trailer is a Bob Yak.
Thanks!
Hi there,

You require 3/8 x 26.

Thanks
Bob nutz for NuVinci 380SE hub?
By
22 Mar 2018
eBike Riese & Muller 'New Charger GH Nuvinci 380SE Hub and Gates carbon belt drive. Axle is 183mm length. I think I know what nut set I want, but you guys are the experts. Will be towing a Bob Ibex trailer - hopefully! Your assistance is appreciated. Best regards, Keith
Hi there,

You need the 10 X 1 option - SJS Cycles part number : 1075T10

Thanks
What Size do I need for a BMC Roadmachine RM02 105 2017 touring
By
07 Aug 2017
Hi, these Nutz are for wheels with solid axles, like hub gears or inexpensive Shimano hubs. I believe from some internet research your bike has Novatec 30SL wheels. It is very likely that you need 'BOB YAK Standard Quick Release skewer - Suit 126.5 mm - 140 mm OLN' our part 1072. This is a direct replacement for the skewer in your wheel. Thanks.
Size?
By
19 Apr 2017
Hi - I Have A Mango Fixie & Need To Attach My Bob Trailer. I Just Received The 3/8-26 Nuts But They Are Too Small. What Size Do I Need? The Wheel Is Here Https://Www.Mangobikes.Com/Shop/Parts/Wheels/Mango-Bikes-Single-Speed-Wheel-Rear-Flip-Flop/
Hello.

I would advise that you that the size you need would be 10 x 1 as this is the only size larger that we have, although as we do not have the hub in our stocks we can not know for sure.

Thanks.
Will These Work With Pre 2000 Trailer Pin?
By
18 Mar 2017
If not which accessory could I use? Thanks.
(Looking for solution for either straight through or alfine hub)
Hi,

These nuts should be fine for use with your pre-2000 trailer.

Thanks.
How Can The Bell Crank Be Attached To The Nutz?
By
11 Mar 2017
Https://Www.Sjscycles.Co.Uk/Hub-Spares/Shimano-Nexus-Bell-Crank-3-Unit/
Hi,

Unfortunately these nuts cannot be used with the Bell Crank found on a Nexus 3spd hub so therefore can't be used at all with the 3spd Nexus hub. It is however fine for use with the more modern 7 and 8spd Nexus hubs.

Thanks.
Will It Fit A New 3 Speed Sturmey Archer Hub ?
By
20 Dec 2016
To fit a new 3 speed sturmey archer / pashley guv'nor
Regards Mark
Hi, yes they will, just make sure you select the Sachs/Sturmey option on the drop down menu & you will be fine.

Regards
Just To Be Sure, Which Bob Yak Solid Axle Nutz Do I Need For A Sram Dual Drive Hub Please? Thanks!
By
04 Sep 2016
0
Hi,

The Dual drive hubs use an unusual thread that is unfortunately not compatible with any of these Bob axle nuts so you will not be able to fit any I'm afraid.

Thanks.
Bob Yak Solid Axle Nutz
By
30 Aug 2016
Just to be sure, which BOB YAK Solid Axle Nutz do I need for Alfine 8 hub please?

Hi,

The correct ones you need for your Alfine hub are the 3/8 x 26 option.

Thanks.
Nut Size & Thread
By
13 Jul 2015
Can you confirm that 3/8 x 26 is needed to fit Shimano Nexus 8 speed hub/axle?
Thanks
Hi,

The 3/8 x 26 nuts are indeed the correctly sized ones for use with your Nexus 8spd hub.

Thanks.
What Size Will I Need
By
29 May 2015
hello, I've got a genesis day one single speed bike and am wondering which of the nuts I would require? 10x1?
Thanks
Hi,

From the specification on Genesis' website your bike has a Shimano rear hub with a solid axle, this means you are correct, you will need the 10x1 option.

Thanks.
A Bob Trailer With No Fitting Attachment On My Bike
By
10 Dec 2014
To fit my bob trailer to my bike(s) what do I need.

Do I need a Solid Axle Nutz or the BOB Spare Quick Release Mounting to attach my bob trailer to my bike

Bike A is a Giant NRS mtn bike inside rear drop 14.5cm, outside rear drop 15.2cm.
Bike B is bike coop revolution tourer 13.2 inside rear drop, outside rear drop 13.5cm
Hi,

Which fitting you need all depends on what sort of wheel you have in your bikes, if your rear wheel uses a solid axle with nuts to do up then you require the Bob Yak solid axle nuts, if your wheel uses a QR hub and skewer then you need on of the Bob Yak replacement skewers. What length you require is dictated by the OLN spacing of you hub, or the distance between the rear dropouts.

Thanks.
Will Any Of The Solid Axle Nuts Suit A Rohloff Hub?
By
22 Nov 2014
Hi,

Rohloff hubs with a nutted axle use a standard 10mm axle so the 10 x 1 option will be compatible with your hub.

Thanks.
Wheel Nuts
By
03 Jun 2014
Hi would a skiiddii trailer fit on these nuts if not do you sell anything that will but I don't want quick release thank
Hi,

The fittings are not that similar to the ones used for the skiiddii trailers, so I don't believe they will work I'm afraid. The only compatible mounting axles we have are quick release ones.

Thanks.
Bob Nutz Which Thread Size?
By
23 May 2014
Which thread size should I order to fit Shimano Alfine 11 speed hub?
Thanks
Hi,

For an Alfine 11 hub you will need the 3/8 x 26 size.
Thanks.
How Do I Know What Size Bolt I Need?
By
18 Jan 2014
I want to but a set of these BOB Solid Axle Nutz but an sunsure what size I need.
My bike is a Genesis IO ID 19" MTB with 26" wheels. The wheel is secured on a 10mm threaded axle with a 15mm headed bolt at present.
Can you advise which of the BOB axle nutz I need to order please.
Hi,

You need these in the 10x1 modern Shimano axle standard.

Thanks.